Polymers and elastomers · Banned
PVC, nylon, acrylic
PVCvalues describe: PVC
Why it's out
Plasticizers, water, monomers.
Where it hides
Cable jackets and quick brackets that never got reviewed.
Properties
The values below are candidate: compiled from the sources named, not yet individually validated. Provisional provenance: NASA outgassing database; O'Hanlon, A User's Guide to Vacuum Technology.
Wet cleaning
| Recipe | not applicable |
|---|---|
| Forbidden | nylon in particular: it comes out of the bath heavier than it went in |
| Limit | water absorption |
Vacuum and outgassing
| Outgassing, unbaked (10 h) | 1×10⁻⁵ to 1×10⁻⁶ mbar·L/s/cm²Sourced in the base: total 2.7×10⁻⁸ to 8.0×10⁻⁶ (6 readings) mbar·L/s/cm². Readings below, or use in a calculation. |
|---|---|
| Vapour pressure | PVC plasticiser is continuous; nylon holds several percent water by mass |
Temperature
| Bake, assembled | 60 °C |
|---|---|
| Metallurgical limit | THE CONDEMNING MECHANISM: plasticiser for PVC, water absorption for nylon, and PVC releases chloride that attacks stainless |
Thermal
| CTE | 70 ppm/K |
|---|---|
| Thermal conductivity | 0.19 W/m·K |
| Specific heat | 1000 J/kg·K |
| Emissivity | 0.9 |
Mechanical
| Strength | 50 tens MPa |
|---|---|
| Tensile | 50 MPa |
| Young's modulus | 3 GPa |
| Density | 1.4 g/cm3 |
Electrical and magnetic
| Relative permeability | 1.0 |
|---|
Engineering
| Availability and cost | commodity |
|---|
Outgassing
9 sourced measurements for this card. A rate means nothing without the pumping time it was read at, so each one states it or declares it missing. The whole base, filters included, is at /tools/outgassing/.
Signature: 1×10⁻⁵ unbaked to 1×10⁻⁸ baked, a drop of 3.0 decades.
| Material as published | Species | State | Pumping time | Rate |
|---|---|---|---|---|
| Methyl methacrylate | total | unbaked | the abscissa of the curve below | 5.60×10⁻⁶ at 1 h to 1.87×10⁻⁶ at 10 h Report a value |
| Nylon | total | unbaked | the abscissa of the curve below | 1.60×10⁻⁵ at 1 h to 8.00×10⁻⁶ at 10 h Report a value |
| Plexiglas | total | unbaked | the abscissa of the curve below | 9.60×10⁻⁷ at 1 h to 3.60×10⁻⁷ at 10 h Report a value |
| Plexiglas | total | unbaked | the abscissa of the curve below | 4.13×10⁻⁶ at 1 h to 2.40×10⁻⁶ at 10 h Report a value |
| Polyamid | total | unbaked | the abscissa of the curve below | 6.13×10⁻⁶ at 1 h to 3.07×10⁻⁶ at 10 h Report a value |
| PVC (24 h at 95 percent RH) | total | unbaked | the abscissa of the curve below | 1.13×10⁻⁶ at 1 h to 2.67×10⁻⁸ at 10 h Report a value |
| Ultrahigh molecular weight polymethylmethacrylate, sample number 2, obtained by frontal polymerization at 60 C for 5 days, molecular weight about 1×10⁷ g per mole | total | baked | the abscissa of the curve below | 1.04×10⁻⁶ at 24 h to 1.60×10⁻⁷ at 264 h Report a value |
| Ultrahigh molecular weight polymethylmethacrylate, sample number 2, obtained by frontal polymerization at 60 C for 5 days, molecular weight about 1×10⁷ g per mole | total | baked | the abscissa of the curve below | 2.13×10⁻⁸ at 24 h to 1.79×10⁻⁸ at 72 h Report a value |
| Ultrahigh molecular weight polymethylmethacrylate, sample number 2, obtained by frontal polymerization at 60 C for 5 days, molecular weight about 1×10⁷ g per mole | total | unbaked | the abscissa of the curve below | 1.56×10⁻⁷ at 24 h to 3.67×10⁻⁸ at 96 h Report a value |
Sources: S-ELSEY-1975-II, S-SEMENOV-IPAC2021. Full citations and conditions at the base and in /data/outgassing.json.
Sources · 1
Used by
Calculators
Apply it
The outgassing base carries this wall, so a machine can be built on it and the figures will read from it.
- 04 Pump Lay a chamber wall in it
- Conductance chain Lay a chamber wall in it